What does IDE (UDMA mode 1) represent?

It is an Ultra DMA transfer mode in the Parallel ATA interface for older PATA drives, offering a theoretical max transfer rate around 25 MB/s.

What is T2 (signal) used for?

T2 is a legacy digital carrier level in North American telecommunications used for medium-capacity leased lines and trunking between switches.

Can I interchange IDE (UDMA mode 1) and T2 (signal) directly?

No, these units relate to different systems—IDE pertains to computer bus transfer timing and T2 to telecom signaling capacity—so conversion is conceptual.

How to Convert from IDE (UDMA mode 1) to T2 (signal)

Convert data transfer rates between IDE (UDMA mode 1), a legacy PATA interface mode, and T2 (signal), a North American telecommunications carrier level. Learn about their differences, uses, and how to translate values.

IDE (UDMA mode 1)

T2 (signal)

Please check your input. It must be a valid numeric value.

IDE (UDMA mode 1) to T2 (signal) Conversion Table

IDE (UDMA mode 1)	T2 (signal)

Custom Unit Conversion Table Generator – Instant Printable Conversion Tables

Start Value

Enter the starting number (positive decimal or integer ≥ 0). Example: 0.1, 1, 5.

End Value

Enter the ending number (positive decimal or integer > Start Value). Example: 10, 50, 100.

Interval

Enter the step size (positive decimal > 0 and < End Value – Start Value). Example: 1.0, 2.5.

IDE (UDMA mode 1) to T2 (signal) Conversion Table
IDE (UDMA mode 1)	T2 (signal)

Explore More Data Transfer Units Converter

What Is This Tool?

This converter translates data transfer measurements from IDE (UDMA mode 1), an older PATA interface transfer mode, to T2 (signal), a historic telecommunications carrier signal rate. It helps compare and analyze transfer capacities across different vintage technologies.

How to Use This Tool?

Input the value measured in IDE (UDMA mode 1) transfer rate.
Select IDE (UDMA mode 1) as the source unit and T2 (signal) as the target unit.
Execute the conversion to see the equivalent T2 (signal) rate.
Use the result to compare or analyze legacy data transfer and telecom capacities.

Key Features

Converts IDE (UDMA mode 1) transfer rates to T2 (signal) units accurately
Supports benchmarking and diagnostics for vintage hardware and telecom lines
Browser-based tool providing easy unit translation between distinct systems
Shows example conversions for quick understanding
Useful for troubleshooting and infrastructure analysis involving legacy systems

Examples

1 IDE (UDMA mode 1) equals approximately 31.6857 T2 (signal).
2 IDE (UDMA mode 1) converts to about 63.3714 T2 (signal).

Common Use Cases

Specifying or diagnosing BIOS and PATA drive transfer modes on vintage computers.
Benchmarking expected maximum throughput of older IDE hard drives and optical devices.
Troubleshooting errors caused by incorrect UDMA mode settings or cable issues.
Comparing data transfer rates between legacy computer hardware and telecom trunk line capacities.
Planning or analyzing historical medium-capacity leased lines and enterprise trunk circuits.

Tips & Best Practices

Use the tool mainly for conceptual comparisons due to different system natures of the units.
Confirm that the IDE (UDMA mode 1) values represent theoretical max transfer rates.
Understand that T2 (signal) refers to nominal telecom circuit capacity, not storage throughput.
Apply conversions in vintage computing diagnostics or historical telecommunications analysis.

Limitations

IDE (UDMA mode 1) rates express theoretical maximum raw speeds, not sustained throughput.
T2 (signal) rates describe nominal telecommunication channel capacity, not direct storage speeds.
Units represent fundamentally different domains – device bus timing versus telecom carrier signals.
The conversion primarily serves conceptual or comparative purposes rather than direct interchangeability.

Frequently Asked Questions

What does IDE (UDMA mode 1) represent?: It is an Ultra DMA transfer mode in the Parallel ATA interface for older PATA drives, offering a theoretical max transfer rate around 25 MB/s.
What is T2 (signal) used for?: T2 is a legacy digital carrier level in North American telecommunications used for medium-capacity leased lines and trunking between switches.
Can I interchange IDE (UDMA mode 1) and T2 (signal) directly?: No, these units relate to different systems—IDE pertains to computer bus transfer timing and T2 to telecom signaling capacity—so conversion is conceptual.

Key Terminology

IDE (UDMA mode 1): An Ultra DMA transfer mode of the Parallel ATA interface offering a theoretical raw transfer rate near 25 MB/s for legacy PATA devices.
T2 (signal): A North American telecommunications carrier level transmitting about 6.312 megabits per second using PCM multiplexing, for medium-capacity leased lines.
Ultra DMA (UDMA): A transfer mode in IDE interfaces that enhances data transmission speed and reliability between a controller and drive.

Quick Knowledge Check

What type of interface uses IDE (UDMA mode 1)?

Fiber Channel

Parallel ATA (PATA)

Ethernet

What does T2 (signal) primarily represent?

Computer transfer speed

Telecommunications carrier level

Wireless data rate

Is the IDE to T2 conversion exact for real-world use?

Yes, perfect for all contexts

No, it is mainly conceptual

Only for fiber networks

Share Us

Similar Calculators

Online Density Units Converter Online Electric Resistance Units Converter Online Velocity Angular Units Converter Online Magnetic Flux Units Converter Online Luminance Units Converter