What does IDE (UDMA mode 0) represent?

IDE (UDMA mode 0) is an Ultra DMA transfer mode for Parallel ATA devices defining interface timing and a maximum raw transfer rate around 16.7 MB/s.

How is gigabit per second (SI definition) different from gibibit per second?

Gigabit per second (SI) is based on decimal units of 10^9 bits per second, whereas gibibit per second uses a binary base of 2^30 bits per second.

Why should I convert IDE (UDMA mode 0) speeds to gigabit per second?

Converting these rates helps compare legacy device speeds with modern network transfer rates to aid in performance evaluation and system upgrades.

How to Convert from IDE (UDMA mode 0) to Gigabit/second (SI def.)

Learn how to convert data transfer rates from IDE (UDMA mode 0), a legacy PATA/IDE interface mode, to gigabit per second (SI definition), used widely in networking and communications.

IDE (UDMA mode 0)

Gigabit/second (SI def.)

Please check your input. It must be a valid numeric value.

IDE (UDMA mode 0) to Gigabit/second (SI def.) Conversion Table

IDE (UDMA mode 0)	Gigabit/second (SI def.)

Custom Unit Conversion Table Generator – Instant Printable Conversion Tables

Start Value

Enter the starting number (positive decimal or integer ≥ 0). Example: 0.1, 1, 5.

End Value

Enter the ending number (positive decimal or integer > Start Value). Example: 10, 50, 100.

Interval

Enter the step size (positive decimal > 0 and < End Value – Start Value). Example: 1.0, 2.5.

IDE (UDMA mode 0) to Gigabit/second (SI def.) Conversion Table
IDE (UDMA mode 0)	Gigabit/second (SI def.)

Explore More Data Transfer Units Converter

What Is This Tool?

This tool enables conversion between IDE (UDMA mode 0), a legacy data transfer mode for Parallel ATA devices, and gigabit per second using the SI definition, a standard unit for network transfer rates.

How to Use This Tool?

Enter the value in IDE (UDMA mode 0) units you wish to convert.
Select the target unit as gigabit per second (SI def.).
Initiate the conversion to view corresponding transfer rates in gigabit per second.

Key Features

Converts IDE (UDMA mode 0) data transfer rates to gigabit per second (SI def.) values.
Uses an established conversion factor linking legacy device speeds with modern network rates.
Helps compare and analyze legacy and modern data transfer performance efficiently.

Examples

5 IDE (UDMA mode 0) equals 0.664 gigabit per second (SI def.).
10 IDE (UDMA mode 0) equals 1.328 gigabit per second (SI def.).

Common Use Cases

Specifying or diagnosing throughput of PATA/IDE drives.
Troubleshooting BIOS or driver DMA timing for performance issues.
Comparing legacy interface speeds when upgrading systems to faster networks.

Tips & Best Practices

Remember that IDE (UDMA mode 0) rates are byte-based, while gigabit per second is bit-based, so interpret results accordingly.
Use the converter to estimate nominal maximum data transfer rates, not practical throughput values.
Apply conversions when evaluating legacy hardware in relation to modern networking equipment.

Limitations

The conversion reflects nominal maximum rates and does not factor in data transfer overhead or real-world throughput variability.
Unit differences between byte-based and bit-based rates require careful attention in interpreting conversions.

Frequently Asked Questions

What does IDE (UDMA mode 0) represent?: IDE (UDMA mode 0) is an Ultra DMA transfer mode for Parallel ATA devices defining interface timing and a maximum raw transfer rate around 16.7 MB/s.
How is gigabit per second (SI definition) different from gibibit per second?: Gigabit per second (SI) is based on decimal units of 10^9 bits per second, whereas gibibit per second uses a binary base of 2^30 bits per second.
Why should I convert IDE (UDMA mode 0) speeds to gigabit per second?: Converting these rates helps compare legacy device speeds with modern network transfer rates to aid in performance evaluation and system upgrades.

Key Terminology

IDE (UDMA mode 0): An Ultra DMA transfer mode 0 for Parallel ATA devices defining nominal maximum raw transfer speeds of about 16.7 MB/s.
Gigabit per second (SI def.): A data transfer rate unit equal to 1 billion bits per second (10^9 bits/s), commonly used in networking communications.
Conversion Rate: The factor used to translate data transfer values from IDE (UDMA mode 0) to gigabit/second (SI def.) is 0.1328.

Quick Knowledge Check

What does the IDE (UDMA mode 0) unit measure?

Network cable length

Data transfer rate for Parallel ATA devices

Processor clock speed

A gigabit per second (SI def.) is equivalent to how many bits per second?

1,000,000,000 bits per second

1,073,741,824 bits per second

16.7 megabytes per second

Why must you be careful interpreting conversions between IDE (UDMA 0) and gigabit/second?

They use different base units: bytes vs. bits

They measure completely unrelated concepts

They use identical measurement units

Share Us

Similar Calculators

Online Density Units Converter Online Electric Resistance Units Converter Online Velocity Angular Units Converter Online Magnetic Flux Units Converter Online Luminance Units Converter