What is IDE (UDMA mode 0)?

IDE (UDMA mode 0) is an Ultra DMA transfer mode for Parallel ATA devices defining nominal maximum raw data transfer rates used for DMA transfers.

What is Fast Ethernet?

Fast Ethernet is a family of IEEE 802.3 standards providing a nominal data rate of 100 megabits per second, used commonly for local area networking.

Why is there a difference in units between IDE and Ethernet speeds?

IDE (UDMA mode 0) data rates are measured in bytes per second, while Ethernet speeds are in bits per second, affecting numeric values and interpretation.

How to Convert from IDE (UDMA mode 0) to Ethernet (fast)?

Convert data transfer rates from IDE (UDMA mode 0) to Fast Ethernet, useful for comparing legacy PATA/IDE drive speeds with Ethernet network speeds for performance evaluation and system upgrades.

IDE (UDMA mode 0)

Ethernet (fast)

Please check your input. It must be a valid numeric value.

IDE (UDMA mode 0) to Ethernet (fast) Conversion Table

IDE (UDMA mode 0)	Ethernet (fast)

Custom Unit Conversion Table Generator – Instant Printable Conversion Tables

Start Value

Enter the starting number (positive decimal or integer ≥ 0). Example: 0.1, 1, 5.

End Value

Enter the ending number (positive decimal or integer > Start Value). Example: 10, 50, 100.

Interval

Enter the step size (positive decimal > 0 and < End Value – Start Value). Example: 1.0, 2.5.

IDE (UDMA mode 0) to Ethernet (fast) Conversion Table
IDE (UDMA mode 0)	Ethernet (fast)

Explore More Data Transfer Units Converter

What Is This Tool?

This tool allows you to convert data transfer rates between IDE (UDMA mode 0), a legacy storage interface standard, and Fast Ethernet, a common network speed standard. It helps in comparing these two different data transfer units for troubleshooting, diagnostics, or planning upgrades.

How to Use This Tool?

Enter the value in IDE (UDMA mode 0) units that you wish to convert.
Select Ethernet (fast) as the target unit for the conversion.
View the converted value representing the equivalent Fast Ethernet data rate.
Use the result to compare or analyze data transfer speeds between legacy and modern interfaces.

Key Features

Converts data transfer rates from IDE (UDMA mode 0) to Fast Ethernet.
Based on standardized transfer speeds for legacy PATA/IDE devices and 100 Mbps Ethernet.
Provides clear numeric conversion factors for easy comparison.
Useful for IT diagnostics, legacy system upgrades, and network planning.

Examples

1 IDE (UDMA mode 0) = 1.328 Ethernet (fast)
10 IDE (UDMA mode 0) = 13.28 Ethernet (fast)

Common Use Cases

Comparing data throughput between legacy PATA/IDE hard drives and Ethernet networks.
Evaluating performance differences for system upgrade planning.
Troubleshooting data transfer issues across mixed technology environments.
Assessing network speed capabilities in small office or home LAN setups.

Tips & Best Practices

Remember that IDE (UDMA mode 0) uses bytes per second while Ethernet (fast) is measured in bits per second.
Use conversion results as approximate comparisons due to protocol overhead and environmental factors.
Consider the age and technology differences when interpreting conversion outcomes.
Use this conversion as a guide for diagnosing or planning, not as a precise real-world throughput measurement.

Limitations

Conversion compares raw data rates that differ in units (bytes vs bits), affecting interpretation.
IDE (UDMA mode 0) is outdated and may have limited relevance with current high-speed technologies.
Practical transfer speeds can vary due to protocol overhead and bus efficiency factors.

Frequently Asked Questions

What is IDE (UDMA mode 0)?: IDE (UDMA mode 0) is an Ultra DMA transfer mode for Parallel ATA devices defining nominal maximum raw data transfer rates used for DMA transfers.
What is Fast Ethernet?: Fast Ethernet is a family of IEEE 802.3 standards providing a nominal data rate of 100 megabits per second, used commonly for local area networking.
Why is there a difference in units between IDE and Ethernet speeds?: IDE (UDMA mode 0) data rates are measured in bytes per second, while Ethernet speeds are in bits per second, affecting numeric values and interpretation.

Key Terminology

IDE (UDMA mode 0): An Ultra DMA transfer mode for Parallel ATA devices with a maximum nominal raw data rate around 16.7 megabytes per second.
Fast Ethernet: A standard IEEE 802.3 Ethernet family providing 100 megabits per second data rate commonly used for local area networks.
Data Transfer Rate: The speed at which data is moved from one device or medium to another, often expressed in bits or bytes per second.

Quick Knowledge Check

What unit does IDE (UDMA mode 0) typically use to express data transfer rate?

Bits per second

Bytes per second

Packets per second

What nominal data rate does Fast Ethernet provide?

100 megabits per second

16.7 megabytes per second

1 gigabit per second

Why should you be cautious interpreting conversion results between IDE and Ethernet?

Because of protocol overhead and unit differences

Because conversions are exact for all scenarios

Because both units measure latency

Share Us

Similar Calculators

Online Density Units Converter Online Electric Resistance Units Converter Online Velocity Angular Units Converter Online Magnetic Flux Units Converter Online Luminance Units Converter