What does IDE (UDMA mode 3) represent?

IDE (UDMA mode 3) is a Parallel ATA transfer mode providing a theoretical maximum raw transfer rate of about 44.4 MB/s, commonly used in legacy PATA/IDE drives.

What is STS192 (signal) used for?

STS192 (signal) is a SONET synchronous transport signal level used primarily in high-speed carrier backbone and long-haul telecom links.

Why convert from IDE (UDMA mode 3) to STS192 (signal)?

Users convert these units to compare legacy storage data rates with modern high-speed network signal levels for compatibility, integration, and performance analysis.

How to Convert from IDE (UDMA mode 3) to STS192 (signal)?

Convert data transfer rates from legacy IDE (UDMA mode 3) to high-speed STS192 (signal) values using our online converter for accurate comparisons and network integration.

IDE (UDMA mode 3)

STS192 (signal)

Please check your input. It must be a valid numeric value.

IDE (UDMA mode 3) to STS192 (signal) Conversion Table

IDE (UDMA mode 3)	STS192 (signal)

Custom Unit Conversion Table Generator – Instant Printable Conversion Tables

Start Value

Enter the starting number (positive decimal or integer ≥ 0). Example: 0.1, 1, 5.

End Value

Enter the ending number (positive decimal or integer > Start Value). Example: 10, 50, 100.

Interval

Enter the step size (positive decimal > 0 and < End Value – Start Value). Example: 1.0, 2.5.

IDE (UDMA mode 3) to STS192 (signal) Conversion Table
IDE (UDMA mode 3)	STS192 (signal)

Explore More Data Transfer Units Converter

What Is This Tool?

This converter translates data transfer rates from IDE (UDMA mode 3), a legacy Parallel ATA transfer mode, into STS192 (signal), a high-speed synchronous transport signal used in telecommunications. It enables users to understand and compare throughput rates across these different technological domains.

How to Use This Tool?

Enter the value in IDE (UDMA mode 3) units you want to convert
Select STS192 (signal) as the target unit for conversion
Click the convert button to see the equivalent STS192 (signal) value
Use the example calculations for reference and validation

Key Features

Converts IDE (UDMA mode 3) transfer rates to STS192 (signal) units based on theoretical maximum speeds
Facilitates comparison between legacy PATA/IDE data rates and modern high-speed carrier signal levels
Browser-based and user-friendly interface for quick and easy data conversion
Provides example calculations to guide users through the conversion process

Examples

Converting 5 IDE (UDMA mode 3) results in approximately 0.2009 STS192 (signal)
Converting 10 IDE (UDMA mode 3) yields around 0.4019 STS192 (signal)

Common Use Cases

Comparing throughput in legacy PATA/IDE drive documentation with modern networking signals
Supporting hardware benchmarking and compatibility checks in system refurbishing
Planning and analyzing telecommunications carrier networks involving mixed legacy and high-speed equipment
Interpreting data transfer modes for BIOS or firmware configuration on older PCs

Tips & Best Practices

Ensure you understand the significant difference in scale between IDE (UDMA mode 3) and STS192 signals
Use the conversion primarily for theoretical and comparative analysis, not for direct operational equivalence
Consult network or hardware documentation to contextualize your conversions appropriately
Refer to example conversions to verify your input and results

Limitations

Conversion results often yield small fractional values because IDE (UDMA mode 3) rates are much lower than STS192 bandwidth
Based on theoretical maximum transfer rates without considering overhead, protocol inefficiencies, or encoding effects
The units represent fundamentally different technologies, limiting direct operational equivalence across contexts

Frequently Asked Questions

What does IDE (UDMA mode 3) represent?: IDE (UDMA mode 3) is a Parallel ATA transfer mode providing a theoretical maximum raw transfer rate of about 44.4 MB/s, commonly used in legacy PATA/IDE drives.
What is STS192 (signal) used for?: STS192 (signal) is a SONET synchronous transport signal level used primarily in high-speed carrier backbone and long-haul telecom links.
Why convert from IDE (UDMA mode 3) to STS192 (signal)?: Users convert these units to compare legacy storage data rates with modern high-speed network signal levels for compatibility, integration, and performance analysis.

Key Terminology

IDE (UDMA mode 3): An Ultra DMA transfer mode for Parallel ATA interfaces providing about 44.4 MB/s raw data transfer with minimal CPU involvement.
STS192 (signal): An electrical framing rate in the SONET family indicating 192 times the STS-1 rate, equivalent to 9.95328 Gbit/s, used in high-speed telecom transport.
SONET: Synchronous Optical Network, a standard for high-speed synchronous data transfers primarily in telecommunications.

Quick Knowledge Check

What is the approximate theoretical maximum transfer rate of IDE (UDMA mode 3)?

About 44.4 MB/s

About 9.953 Gbit/s

About 100 MB/s

STS192 (signal) corresponds to what type of communication system?

Parallel ATA interface

SONET synchronous transport

Optical disk drive signaling

Why might conversion results yield very small values?

Because STS192 is much faster than IDE (UDMA mode 3)

Because the units are identical

Because IDE (UDMA mode 3) is faster than STS192

Share Us

Similar Calculators

Online Density Units Converter Online Electric Resistance Units Converter Online Velocity Angular Units Converter Online Magnetic Flux Units Converter Online Luminance Units Converter