What is IDE (UDMA mode 3)?

IDE (UDMA mode 3) is a legacy Ultra DMA transfer mode for Parallel ATA interfaces offering a theoretical maximum speed of approximately 44.4 MB/s, used primarily in older PATA devices.

Why convert IDE (UDMA mode 3) rates to gigabyte/second (SI def.)?

Converting to gigabyte/second (SI def.) allows comparison of legacy transfer rates with modern storage and network units that use decimal-based definitions.

Is this conversion exact for real-world speeds?

No, the conversion is based on theoretical maximums; actual transfer speeds may vary due to many factors including hardware and workload.

How to Convert from IDE (UDMA mode 3) to Gigabyte/second (SI def.)?

Learn how to convert data transfer rates from IDE (UDMA mode 3), a legacy parallel ATA mode, to the modern gigabyte per second (SI definition) unit for accurate performance comparison.

IDE (UDMA mode 3)

Gigabyte/second (SI def.)

Please check your input. It must be a valid numeric value.

IDE (UDMA mode 3) to Gigabyte/second (SI def.) Conversion Table

IDE (UDMA mode 3)	Gigabyte/second (SI def.)

Custom Unit Conversion Table Generator – Instant Printable Conversion Tables

Start Value

Enter the starting number (positive decimal or integer ≥ 0). Example: 0.1, 1, 5.

End Value

Enter the ending number (positive decimal or integer > Start Value). Example: 10, 50, 100.

Interval

Enter the step size (positive decimal > 0 and < End Value – Start Value). Example: 1.0, 2.5.

IDE (UDMA mode 3) to Gigabyte/second (SI def.) Conversion Table
IDE (UDMA mode 3)	Gigabyte/second (SI def.)

Explore More Data Transfer Units Converter

What Is This Tool?

This converter transforms data transfer rates measured in IDE (UDMA mode 3), a legacy PATA interface transfer mode, into gigabytes per second using the SI prefix. It helps relate older hardware speeds to current standard units.

How to Use This Tool?

Enter the data transfer rate value in IDE (UDMA mode 3).
Select the source unit as IDE (UDMA mode 3).
Choose the target unit as gigabyte/second (SI def.).
Click the convert button to get the equivalent transfer rate in gigabyte/second.
Use the result to compare or document data transfer speeds across technologies.

Key Features

Converts data transfer speeds from IDE (UDMA mode 3) to gigabyte/second (SI definition).
Uses a fixed conversion rate based on theoretical maximum transfer speeds.
Helps compare legacy PATA/IDE throughput with modern high-performance storage rates.
Browser-based tool requiring no installation.
Supports straightforward user input and immediate result display.

Examples

1 IDE (UDMA mode 3) equals 0.05 gigabyte/second (SI def.).
10 IDE (UDMA mode 3) equals 0.5 gigabyte/second (SI def.).

Common Use Cases

Specifying or comparing throughput for legacy PATA/IDE hard and optical drives in technical documents.
Configuring or interpreting drive transfer modes in BIOS or firmware for older PCs.
Benchmarking and troubleshooting legacy PATA/IDE storage devices.
Planning data center capacity by understanding older device rates relative to modern units.
Refurbishing legacy systems and integrating them with current storage technologies.

Tips & Best Practices

Remember IDE (UDMA mode 3) rates represent theoretical maximum speeds under ideal conditions.
Use the conversion to facilitate understanding but consider actual real-world performance variations.
Keep in mind gigabyte (SI) uses decimal-based units differing from binary-based byte definitions.
Refer to manufacturer datasheets or benchmarks to verify transfer rates when possible.

Limitations

IDE (UDMA mode 3) transfer speeds are legacy and significantly slower than modern standards.
Converted values reflect theoretical maximum rates, not actual sustained throughput.
Differences between binary and decimal byte units may affect precise comparisons.
This conversion applies primarily for understanding and documentation rather than performance guarantees.

Frequently Asked Questions

What is IDE (UDMA mode 3)?: IDE (UDMA mode 3) is a legacy Ultra DMA transfer mode for Parallel ATA interfaces offering a theoretical maximum speed of approximately 44.4 MB/s, used primarily in older PATA devices.
Why convert IDE (UDMA mode 3) rates to gigabyte/second (SI def.)?: Converting to gigabyte/second (SI def.) allows comparison of legacy transfer rates with modern storage and network units that use decimal-based definitions.
Is this conversion exact for real-world speeds?: No, the conversion is based on theoretical maximums; actual transfer speeds may vary due to many factors including hardware and workload.

Key Terminology

IDE (UDMA mode 3): An Ultra DMA transfer mode for Parallel ATA interfaces with a theoretical maximum transfer rate around 44.4 MB/s, used in legacy PATA devices.
Gigabyte/second (SI def.): A data transfer rate unit representing 1 gigabyte equal to 10^9 bytes transferred per second, based on decimal SI prefixes.
Theoretical Maximum: The highest possible speed under ideal conditions as specified by technical standards, which may not match actual performance.

Quick Knowledge Check

What type of transfer mode is IDE (UDMA mode 3)?

A modern SATA mode

A legacy Ultra DMA mode for Parallel ATA

A network transfer protocol

What does a gigabyte/second (SI def.) represent?

1 × 10^9 bytes transferred every second

1 × 2^30 bytes transferred every second

1 × 10^6 bytes transferred every second

Why should real-world performance be considered when using this converter?

Because IDE UDMA modes are newer and faster than SI units

Because theoretical maximums do not always reflect actual throughput

Because conversions produce inaccurate numbers

Share Us

Similar Calculators

Online Density Units Converter Online Electric Resistance Units Converter Online Velocity Angular Units Converter Online Magnetic Flux Units Converter Online Luminance Units Converter